Multimedia

Q1

Can I connect a Surround Sight camera to an LCD monitor?

A1

Yes. The CCA188 camera power supply has an RCA composite video output that can go to any monitor with composite video in.

voltar para o topo da página

Q2

Does Clarion make an A/V switcher?

A2

Yes, there are two available. The MSS7100 has 1 radio, 3 A/V and 1 Surround Sight CCD inputs and can have up to four independent zones. Station 1 id dedicated to the driver and Stations 2-4 have headphone outputs. The MSS430 switcher has 4 A/V RCA inputs, and 3 independent zones. It includes 3 wired remote controls for the zones, and RCA A/V outputs.

voltar para o topo da página

Q3

DVS9755Z - VIDEO SWITHCING

A3

Problem: I have installed this DVD Player and I have noticed that I have little to no bass response. I go through the pink noise and I can hear something coming from my subwoofers but when I play a DVD or CD, no subwoofer. What am I doing wrong?

Solution: You need to press ADJUST button on the remote faceplate till you reach FILTER. Then press the ENT button. Once you are in their press the left or right arrows to go to the FRONT SPEAKER crossover and change that to anyone of the following points 50Hz, 80Hz, or 120Hz. You will need to press either the up or down arrows to change these points. Then press ENT button and you are done and will have your subwoofer response back.

voltar para o topo da página

Q4

DVS9755Z - SUBWOOFER CONTROL

A4

Problem: I am using an audio/video source (VCR, TV Tuner, etc…) to go into the Audio/Video input on this unit. I can hear it because I have it on analog one but I can’t see the movie. What am I doing wrong?

Solution: You will need to press the V.SRC button on the remote control so that it will change the video to the outside source. It will read V-OUT on the display. When you go back to INTERAL and you can’t see the video, press the same button (V-OUT) and it will change it over to V-IN.

voltar para o topo da página

Q5

How about TV tuners?

A5

The C-Bus TTX7101, the CeNet 7501z and the TTX7601 Stand alone FM transmitter tuners offer diversity antenna inputs for better reception. The versatile TTX7101 can be operated by the appropriate C-Bus radio or stand alone with the CAA357 kit. Its built-in modulator works with any radio and has 2 RCA A/V and a Surround Site CCD input. The TTX7501z is controlled by a CeNet source unit and has 1 A/V input (requires CCA389 cable) and Surround Sight CCD inputs. The TTX7601 has stereo TV audio, and 1 A/V and 1 Surround Sight CCD input. It has a built-in FM transmitter that requires no antenna connections to the factory radio, and includes an IR remote control and IR eye.

voltar para o topo da página

Q6

VRX610 AND DVS9755Z WORKING TOGETHER

A6

Using the internal power of the VRX610 with the DVS9755z.

Solution: Use a CCA-389 cable from the back of the VRX610 to the FRONT audio output and the VIDEO output of the DVS9755z.

Program the DVS9755z as followed:
・Press ADJUST then the right arrow to read SP-SEL (speaker select) then ENT.
・Press rt. arrow then ENT, CTR-SP, then down arrow to turn off center channel output.
・Press rt. arrow then ENT, SRD-SP, then down arrow to turn off rear speaker output.
・Press rt. arrow then ENT, SUB-WF, then down arrow to turn off subwoofer output.
・Press ENT to save these changes.

voltar para o topo da página

Q7

VRX610 MONITOR LOCK

A7

・Using a CCA-389 cable in the back of the VRX610 you can input a video source. When you   do this, now you can watch that video source and listen to one of the following: AM/FM, CD   Changer, or TV Tuner. This is called Monitor Lock.
・Follow this steps when the unit is open to get this done.
・Press the OPEN / M-LOCK button that is on top of the unit.
・This will allow the video source from the CCA-389 to display on the screen.
・Press the FUNC to get another source to play through the system.
・Press the OPEN / M-LOCK to remove that video source from the screen.

voltar para o topo da página

Q8

VRX815 SCREEN SAVERS AND PATTERNS

A8

The unit has 2 patterns and 6 colors for the screen display along with 4 motion patterns and 4 sprite patterns. You can get to these screens by pressing the DISP button while the screen is in the open position.

voltar para o topo da página

Q9

VRX815 MONITOR LOCK MODE

A9

If they wanted to do the Monitor Lock feature on this unit it will need a CCA389 cable that will plug into the CCD/M.LOCK input on the tuner box. This is ONLY a VIDEO INPUT not an Audio input. You can “Y” out your video source and plug it into this cable. You then can watch whatever source is plugged into it and listen to AM/FM, CD, CD Changer or what you have plugged into either of the other Audio Video inputs. Press the M.LOCK button on the front of the screen and that video source will come up, then press the FUNC till you reach the audio source that you want. The screen will stay on that source for 5 seconds and then go back into M.LOCK. If you want to stop doing this feature then all you have to do is press M.LOCK again. (Except when using the DVS9755z in SLAVE MODE)

voltar para o topo da página

Q10

VRX815 ADDING DVS9755Z

A10

Using this unit with a DVS9755z, all it takes is a CeNet cable and make sure that you now have the DVS9755z in the SLAVE mode. Also place the VIDEO output of the DVS9755z to the DVD VIDEO input of the VRX815. There is a switch on the back of the unit that reads M/S, please move it over to S. What this will allow you to control the volume through the VRX815 by aiming your remote at the IR on the front of the VRX815. You can also hide the display of the DVS9755z after you set up all your filters and gains on the DVD player.

voltar para o topo da página

Q11

VRX815 STATION TITLE

A11

To input a radio station call letters or a CD Name all you have to do is touch the screen and it will read FUNCTION, P.CH SELECT, SUB MODE, and TITLE INPUT. Then tap the TITLE INPUT and then start to input the name that you desire. After you finish press and hold the MEMO button on the screen till it gives you a long BEEP and the screen will go back and show you how it looks.

voltar para o topo da página

Q12

VRX815 Slave Controlling the DVS9755z

A12

When the DVS9755z’s rear switch is set in the slave mode, the VRX815 will control most of the DVS9755z’s functions either from its touch screen, or from its front panel controls or IR remote control.
Detail Information >

voltar para o topo da página

Q13

Using a DVD player with the VRX815 in the Non-Slaved Mode

A13

You can use the DVS9755z with the VRX815 in a non-slaved mode.
Detail Information >

voltar para o topo da página

Q14

I have connected the VRX815 to the VCZ625 with the CeNET cable and the VCZ625 is not working. I have the VCZ625 under CeNET and have reset the system and the VCZ625 is still not working. How can I get these two items to work together?

A14

Well these two will not work together using the CeNET cable. You will have to use the RCA audio output from the VCZ625 and connect it to one of the Audio/Video inputs on the VRX815. You will need to also hook up the IR Receiver so that you can control the VCZ625.

voltar para o topo da página

Q15

When using the VS715 with a VRX610z/VRX6671z, the “DVD” logo scrolls across the screen during start up mode. Once the start up mode is completed and movie begins, the video picture is fine. Also, when a CD is played in the VS715, the “DVD” logo scrolls across the screen, making it impossible to read any of the track information.

A15

Set the video format on the VS715 and VRX610z/VRX6671z to PAL mode. Note: On the VS715, it has to be set on “PAL,” not “PAL 60.”

Draw Back:
Using the Aux input on the VS715 requires the VS715 and VRX610z/VRX6671z to be put into NTSC mode

Other Notes:
Using the TTX7501z TV tuner with the VS715 and VRX610z/VRX6671z works, but requires the VRX610z/VRX6671z to be put back into NTSC mode when the Aux input of the TTX7501 is being used.

voltar para o topo da página

Q16

The VS715 has an uncharacteristic high audio output when playing CD’s, but not with DVD’s. This high audio output has resulted in distorted audio when CD’s are being played. This problem has been found when the VS715 is used with the following radios: MAX2256, VRX8271, VRX6671z, VRX610, and VRX815.

A16

Modify the RCA patch cords from the VS715 to the head unit. This modification simply requires a 15l ohm resistor to be installed inline with the center conductor of the RCA.

Parts required from Radio Shack:
271-1127  15k-Ohm Resistors
274-337  Inline Phono Jacks (Female RCA Jack) (4 pack)
1) Cut a RCA patch cord in half
2) Solder a 15k-Ohm resistor to the center conductor of a Female RCA Jack.
3) Solder the center conductor of the RCA to the resistor.
4) Solder the outer shielding to the conductor of the Female RCA Jack.

voltar para o topo da página

Q17

When I select CCD input the display says "AUDIO SOURCE ONLY".

A17

The unit has an orange lead that must see a ground in order to display video. To comply with State/Federal laws, this lead must be tied into the vehicle's parking brake circuit if the unit is placed within the driver's view.

voltar para o topo da página

voltar para o topo da página